Vermont Castings VC0620AP-NP

Replacement stainless steel burner. Includes venturi mounting bolts/screws. Venturi not included, sold separately.

NOTE: The original cast brass and cast iron burners are no longer available. This replacement stainless steel version is slightly smaller, but supports the same amount of gas with good heat distribution. The stainless steel version will not screw down into the base of the grill, but simply sits in the bottom of the grill using adjustable support brackets, which are included.

Part Number: AZ001504-SS
Dimensions: 15 7/8” x 8”
Material: stainless steel
Weight: 2.5

AZ001504-R Replacement cast iron burner. Includes venturi mounting bolts. Venturi not included, sold separately. Replaces original Great Outdoors part# AZ001504.

Fits models:

• 5500
• 6000
• 6100
• 7000
• 7500

NOTE: The original Great Outdoors cast brass and cast iron burners are no longer available. This replacement burner is slightly larger, but fully functional. It's ”legs” are not threaded, so it simply sits in the bottom of the grill.

Part Number: AZ001504-R
Dimensions: 15 1/2” x 8”
Material: cast iron
Weight: 7.0

Spider exclusion screens. Installs over venturi air shutters to keep spiders out. Approximately 7/8” in diameter and 1” long.

Part Number: 70002
Dimensions: 1” x 7/8”
Material: stainless steel
Weight: 0.1

AZ000505-R Replacement venturi tube. Includes gasket and screws. Replaces original Great Outdoors part# AZ000505.

Fits models:

• 6000
• 6100
• 7000
• 7500

Part Number: AZ000505-R
Dimensions: 2 15/16” x 4 1/8”
Material: zinc plated steel
Weight: 0.7

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, almost 6 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Dimensions: 15” x 11 1/8”
• Made in USA .
• Sold individually.

Part Number: CLA-GS0006
Dimension Front-to-Back: 15”
Dimension Side-to-Side: 11 1/8”
Material: stainless steel
Weight: 5.8

Premium quality stainless steel cooking grid. Far superior to the porcelain coated steel grids it replaces.

• Made in USA
• 304 commercial grade stainless steel
• Solid .225 diameter stainless rods
• Sold individually

Fits grill by Arkla, Arklamatic, Charbroil, Charmglow, Embermatic, Great Outdoors, Kenmore, Kmart, Martha Stewart, Roper, Vermont Castings, Weber. May fit others.

Part Number: 58671-SS
Dimension Front-to-Back: 14 3/4”
Dimension Side-to-Side: 21 1/2”
Material: Stainless steel
Weight: 5

Commercial 304 grade stainless steel cooking grid with 1/4” diameter rods. Sold individually. Made in USA .

Part Number: CG-53SS
Dimension Front-to-Back: 14 3/4”
Dimension Side-to-Side: 21 1/2”
Material: Stainless steel
Weight: 5

Carbon steel rock grate with 1/4” rods. Made in USA .

Replaces Vermont Castings factory part# AF000203

Part Number: CLA-RX0007
Dimensions: 13” x 19”
Material: carbon steel
Weight: 4.5

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal collector box with electrode and wire. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

Collector box and ceramic electrode with male spade connector. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, but no ground wire, see ground wire 03620.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000103

Part Number: 03800
Material: ceramic
Weight: 0.2

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000203

Part Number: 03400
Weight: 0.1

Rotary piezo spark generator. Two round connector leads send spark to both main burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Vermont Castings factory part# AN000303

Part Number: 03220
Weight: 0.2

Silver plastic control knob. Replaces original part# 50002552. Can also be used to replace knob part# AZ000703.

• Off position D-Value: 6 o'clock
• Knob diameter: 2 3/16”
• Socket diameter: 8mm
• Knob shaft: None

Part Number: 02552
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.1

24” LP hose and regulator with QCC-1 connection.

• For use on ”new style” QCC-1 tanks.
• Consists of hose part# 01000 and regulator part# 00920.
• Hose end with SAE 3/8” female flare fitting connects to grill.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. See our flare fitting description for information on measuring and sizes.

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

Premium quality stainless steel warming rack. You simply can't buy a better quality warming rack than this, which weighs in at almost 5lbs of solid 304 grade stainless steel. This super heavy-duty warming rack was made to replace AF000303, the porcelain coated steel racks found on BBQ grills made by The Great Outdoors Grill Company, but can fit in any grill with 23 inches or more for the rack to sit on.

• Far superior to the original porcelain coated steel rack
• Rests on your existing cooking grids.
• Solid 1/4” 304 stainless steel rods.
• Stands 3 inches tall.
• Made in USA .

WARNING: Before ordering this universal rack, please verify your grill has enough space to accomodate it. At least 23” inside the closed lid is required.

Replaces Vermont Castings factory part# AF000303

Part Number: AF000303-SS
Dimensions: 6 1/4” x 22 3/4”
Material: stainless steel
Weight: 4.8

T manifold for twin valves with 3/8” male flare. Fits Charbroil late model grills with LP hoses crimped to the manifold.

Part Number: 34100
Dimensions: 2” x 1 5/16”
Material: brass
Weight: 0.3

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

Durable 2 5/16” round briquettes

• Self-cleaning
• Control flare-ups while holding an even heat pattern.
• About 53 pieces, covers approximately 275 sq. inches.
• Fits all gas grills

Replaces Vermont Castings factory part# AQ000103

Part Number: BQ-5
Weight: 7.2

6 deluxe chrome plated 22” shish-ke-bab skewers with wooden handles

Part Number: 40538
Material: chrome steel
Weight: 1.1

50-piece ceramic briquette set. Works in all grills designed for briquettes or lava rock. Fits briquette tray parts 94751, 92571 and other simular trays.

Part Number: 41650
Dimensions: 2” x 2”
Material: ceramic
Weight: 7.2

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Cast aluminum griddle

Part Number: 91652
Dimensions: 19 1/2” x 10 3/4”
Material: aluminum
Weight: 3.0

Abrasive scrubbing brush. Ideal for cleaning porcelain grills.

Part Number: 71448
Weight: 0.2