Igniter Components for Vermont Castings grills

wired remote trigger switch

For more information about ignition systems and components, please see article Ignition 101 in our help center for some Vermont Castings grills.

Part Number: 03154
Material: plastic
Weight: 0.1

Universal 5 1/2” jumper wire with female spade ends to close off unused pair of outlets in battery-powered spark generator, or use as an adaptor wire for some Vermont Castings grills.
NOTICE: EACH END HAS A PLASTIC PROTECTOR CAP.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03197
Weight: 0.05

Universal 2 5/8” adapter wire with female round and male spade connectors for some Vermont Castings grills. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory piezo spark generators have male round connectors, while battery operated electronic spark generators usually have male spade connectors.

• Can change male round to male spade
• Can change female spade to female round

ALL

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03198
Weight: 0.05

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover for some Vermont Castings grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Rotary piezo spark generator for some Vermont Castings grills. Two round connector leads send spark to both main burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03220
Weight: 0.2

Rotary piezo spark generator for some Vermont Castings grills. Three round connector leads send spark to both main burners and rotisserie burners. For use with all Ducane models with rear rotisserie burners.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03230
Weight: 0.2

Universal battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has one (1) terminal (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03310
Weight: 0.3

Universal volt battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03320
Weight: 0.3

Universal battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03330
Weight: 0.5

Universal three-outlet battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has three (3) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03333
Dimensions: 2 9/16” x 2”
Weight: 0.5

Universal battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has (5) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03335
Dimensions: 2 5/8” x 2”
Weight: 0.3

Universal four-outlet battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Universal battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has six (6) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03350
Weight: 0.7

Universal battery powered push button ignitor for some Vermont Castings grills.

• 1.5 volt
• Has five (5) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03380
Dimensions: 3 5/16” x 2”
Weight: 0.7

25” wire with female spade connector on one end, and female round connector on the other end for some Vermont Castings grills. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors) for some Vermont Castings grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

Ignition connection wire used to connect battery powered spark generators to electrodes for some Vermont Castings grills. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors for some Vermont Castings grills. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal adapter wire with male round and female spade connectors for some Vermont Castings grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03751
Weight: 0.05

Collector box and ceramic electrode with male spade connector for some Vermont Castings grills. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, but no ground wire, see ground wire 03620.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03800
Material: ceramic
Weight: 0.2

Burner mounted electrode with male spade connector for some Vermont Castings grills. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Part Number: 04010
Material: ceramic
Weight: 0.05

Universal collector box with electrode and wire for some Vermont Castings grills. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

46” Wire with female spade connectors and square plastic connectors for some Vermont Castings grills.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Push-button electronic igniter with four (4) spade connectors for some Vermont Castings grills. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

Universal 3 outlet rotary spark generator for some Vermont Castings grills. Includes knob.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-8B
Weight: 0.3