Vermont Castings CF9055N

Burner mounting plate. This part is used to reinforce the front grill housing so the burner can be mounted to the grill. In some cases, the grill housing has rusted or corroded such that the burner cannot be properly mounted to the front of the grill.

• Sold individually, number required varies. Use one per burner.
• Includes mounting bolt and nut
• Includes extra holes for mounting to grill, if necessary.
• Comes with complete installation instructions.

For models:

• CF9080/85/86
• VCS300/3500/35BI/4000/4005/5000/5005/5010/50BI
• VCS3507/4007/5007/3507BI/5007BI

Made in USA

Part Number: CLA-MS0227
Dimensions: 3 3/4” x 4 15/16”
Material: stainless steel
Weight: 0.11

Burner mounting plate. This part is used to reinforce the front grill housing so the burner can be mounted to the grill. In some cases, the grill housing has rusted or corroded such that the burner cannot be properly mounted to the front of the grill.

• Premium grade stainless steel
• Includes gasket and mounting screw
• Comes with complete installation instructions
• Sold individually.

For models:

• CF9080/85/86
• VCS300/3500/35BI/4000/4005/5000/5005/5010/50BI
• VCS3507/4007/5007/3507BI/5007BI

Part Number: 03501
Dimensions: 3 3/4” x 4”
Material: stainless steel
Weight: 0.16

Commercial premium 304 grade stainless steel burner for Vermont Castings model CF9055N.

Part Number: 13001
Dimensions: 17” x 1”
Material: stainless steel
Weight: 0.8

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually.

Part Number: 61271-UNI
Dimension Front-to-Back: 16 7/16”
Dimension Side-to-Side: 9 1/16”
Material: cast iron
Weight: 5.45

Cast iron cooking grid. Porcelain enameled, glossy finish.

Part Number: 61271
Dimension Front-to-Back: 16 3/8”
Dimension Side-to-Side: 9 1/8”
Material: gloss cast iron
Weight: 7.0

Stainless steel heat plate. Some OEM originals were porcelain coated steel. This stainless version, which resists rust and corrosion better, is far superior to original porcelain part.

Part Number: VCHP1
Dimension Front-to-Back: 14 1/2”
Dimension Side-to-Side: 7 1/4”
Material: stainless steel
Weight: 0.7

SET OF THREE/3 PACK Stainless steel Flame Tamer. Sold individually, number required varies. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0016-X3
Dimension Front-to-Back: 14 1/2”
Dimension Side-to-Side: 7 1/4”
Material: stainless steel
Weight: 3.6

Stainless steel Flame Tamer. Sold individually, number required varies. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Vermont Castings factory part# 50000877

Part Number: CLA-TS0016
Dimension Front-to-Back: 14 1/2”
Dimension Side-to-Side: 7 1/4”
Material: stainless steel
Weight: 1.3

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

Replaces Vermont Castings factory part# 50000431

Part Number: 04010
Material: ceramic
Weight: 0.05

Stainless steel grease pan. Includes grease cup and grease cup holder. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Replaces Vermont Castings factory part# 50001842

Part Number: CLA-DS0099
Dimensions: 9 1/2” x 24 7/8”
Material: stainless steel
Weight: 3.0

Five piece 3/8” natural gas quick disconnect set includes:

• Part ASCPL-2 12ft vinyl 3/8” ID Sturgis hose (3/8” inside diameter outside diameter about 1/2”) with solid brass fittings
• Part ASCPL-3 Sturgis brand 3/8” quick connect brass coupler
• Hansen & Sturgis dust cover
• plastic dust plug
• Plastic 3/8 MPT Snap Tite
• Suitable up to approximately 60,000 BTU.

Part Number: ASCPL-1
Weight: 3.0

12 foot natural gas quick-connect hose.

• The hose end with SAE 3/8” female flare fitting connects to grill.
• Designed for use with quick connect coupling part# 81441
• Hose and coupling also available together as part# 80144.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. (Inside diameter of hose is 3/8” and the outside is about 5/8”.) See our flare fitting description for information on measuring and sizes.

Replaces Vermont Castings factory part# 50000198

Part Number: 81442
Weight: 2.3

Brass 3/8” natural gas quick connect coupling.

• Use with hose #81442.
• Coupling and hose also available together as part# 80144.
  
  See description of part# 80144 for more information and pictures of how part couples with hose.

  Replaces Vermont Castings factory part# 50000915

  
  
  Part Number: 81441
  Dimensions: 2 1/2” x 1 1/8”
  Material: brass
  Weight: 0.4

Genuine OEM Heat indicator. About 2 3/8” wide and 2” high. The threaded stem is about 5 /16” diameter and 1 1/8” long.

Part Number: 10571-6
Weight: 0.12

Skewers for part 92339 kebob tray.

Part Number: 11040
Weight: 0.4

16” Stainless Steel Tong/Turner Combination. 16” multi-use tool with red soft grip rubber inserts. Can be used as a turner, tong or both. Manual lock saves on storage space.

Part Number: 40240
Material: chrome steel
Weight: 0.9

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Stainless steel WOK topper with serving handles. Ideal for seafood and vegatables.

Part Number: 96321
Dimensions: 12 3/4” x 12 3/4”
Material: stainless steel
Weight: 1.6

EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

Part Number: 00030
Weight: 0.1