Sams Y0660LP-2

Cast iron burner for Sams model Y0660LP-2.

Replaces Sams factory part# P1925C

Part Number: 29251
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 6.4

Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..

Part Number: 29251-CSS-X3
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 10.05

Cast stainless steel burner. Tired of changing out rusted cast iron burners? Far superior to the cast iron and brass versions, this burner will probably outlast your grill. Designed to replace cast iron and brass burners of same design..

Part Number: 29251-CSS
Dimensions: 16” x 4 5/8”
Material: cast stainless steel
Weight: 3.35

Cast iron burners. SET OF THREE(3).

Part Number: 29251-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 19.2

Cast iron burner for Sams model Y0660LP-2.

Part Number: CISC-X3
Dimensions: 15 3/4” x 4 3/4”
Material: cast iron
Weight: 15.0

Stainless steel burner mounting bracket. Also called a cross over channel. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Sams factory part# P0220408BA

Part Number: CLA-MS0032
Dimensions: 34 1/4
Material: stainless steel
Weight: 2.2

Aftermarket reversible heavy cast iron cooking grid.

• Sold individually
• Number required varies, check your grill
• Porcelain treated, flat matte finish
• Pointed side is designed for perfect sear marks
• Grooved side captures juices for continous basting

Fits: Broil King 500/625/750 series grills.

NOTE: This aftermarket part, made of the same materials as the original, is a perfect replacement for original part# 22005-281 but at a much lower cost.

Part Number: 22005-281-R
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 6 1/16”
Material: Cast iron
Weight: 5.0

Porcelain steel cooking grid. Porcelain enameled, glossy finish. Sold individually.

Part Number: 51631
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 5/16”
Material: porcelain steel wire
Weight: 4.0

Porcelain steel cooking grids. Porcelain enameled, glossy finish. Sold as a set of three (3). If you prefer a heavier cast iron porcelain enameled glossy finish cooking grid, select four (4) panels of # 65131.

Part Number: 54453
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 31 1/2”
Material: porcelain steel wire
Weight: 15.10

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually.

Part Number: 65131-UNI
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 7 5/8”
Material: cast iron
Weight: 5.55

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually, number required varies, check your grill.

Part Number: 67845-1PC
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 6 1/16”
Material: matte cast iron
Weight: 5.5

Cast iron cooking grids, porcelain treated, flat matte finish for Sams model Y0660LP-2.

Part Number: 67845
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 30 5/16”
Material: matte cast iron
Weight: 27.2

Premium universal cooking grids. Set of three (3) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 18 7/8”
• Side-to-Side: 10 1/2”

Total Side-to-Side: 31 1/2”

Part Number: 68073-UNI-X3
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 31 1/2”
Material: cast iron
Weight: 21.75

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 68073-UNI-X3 for a set of three (3) grids.

Part Number: 68073-UNI
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 10 1/2”
Material: cast iron
Weight: 7.25

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually.

Part Number: 69501
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 1/8”
Material: cast iron
Weight: 4.85

Cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of three (3).

Part Number: 68073
Dimension Front-to-Back: 18 7/8”
Dimension Side-to-Side: 31 11/16”
Material: matte cast iron
Weight: 19.2

Cast iron cooking grid. Porcelain treated, matte finish. Sold individually, number required varies by grill model.

Part Number: CG-71P-CI
Dimension Front-to-Back: 18 3/4”
Dimension Side-to-Side: 7 5/8”
Material: cast iron
Weight: 5.55

Ceramic Flame Tamer. Measures 7” x 8”. Box of 6.

Note: This part is used in racks P1736B, P1739A, P01722021B.

Fits models:

• Y0005XC-1
• Y0005XC-2
• Y0101XC
• Y0202XC
• Y0660LP/NG
• And others

Replaces Sams factory part# P1736A

Part Number: P1736A-R
Dimension Front-to-Back: 7”
Dimension Side-to-Side: 8”
Material: ceramic
Weight: 9.0

Flame Tamer Rack. Heavy duty nickel plated 5/16” steel rod. Each rack holds twelve (12) P01804001A-R ceramic flame tamers (sold separately). Also known as part number P1736A.

NOTE: This is an aftermarket part made to replace original part number P01722021B, which is no longer available.

Fits models:

• MONARCH04
• Y0660
• and others

Replaces Sams factory part# P01722021B

Part Number: P01722021B-R
Dimension Front-to-Back: 17 1/4”
Dimension Side-to-Side: 33 7/16”
Material: nickel plated steel
Weight: 8.95

Replacement steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA .
TEMPORARILY OUT OF STOCK, but more are already on the way. Orders for this part will be filled from new inventory expected to arrive late Aug.

Part Number: CLA1721
Dimension Front-to-Back: 16 7/8”
Dimension Side-to-Side: 9 3/4”
Material: carbon steel
Weight: 3.5

Stainless steel Flame Tamer. For many models, can also be used to replace ceramic flame tamers and the rack that holds them. Made in USA .

Part Number: CLA2721
Dimension Front-to-Back: 16 3/4”
Dimension Side-to-Side: 9 3/4”
Material: stainless steel
Weight: 2.4

Collector box with electrode and connector wire (both ends are female spade)

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P2623D

Part Number: 02624
Material: ceramic
Weight: 0.2

Battery powered push button igniter.

• Has two (2) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502012C

Part Number: IGEIB2-B
Weight: 0.3

Small AA battery powered push button spark generator.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502012C

Part Number: 03342
Weight: 0.3

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502024C

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502024C

Part Number: 03340
Weight: 0.5

Push-button electronic igniter with two (2) spade connectors. Black cap. 1 AAA battery (not included).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG2006
Weight: 0.2

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal 2 5/16” knob.

• Selectable D-Value
• Selectable socket diameter - 6mm or 8mm.
• Selectable shaft length - flush, 1/4”, or 1 5/8”. Shafts can also be trimmed to desired length.
• Includes 6 shaft inserts and set screw.
• Fits any grill with inside bezel diameter greater than 2 5/16” (the knob diameter).

Replaces Sams factory part# P03411011L

Part Number: 02342
Dimensions: 2 5/16” x 2 5/16”
Material: plastic
Weight: 0.20

Black control knob to fit Sam's models for Sams model Y0660LP-2.

Part Number: 03430
Dimensions: 2 3/16” x 2 3/16”
Material: plastic
Weight: 0.2

Straight thru L.P regulator with 28” hose. Adequate to 90,000 BTU.

Replaces Sams factory part# P3632K

Part Number: HR-6B
Dimensions: 28
Weight: 1.50

24” LP hose and regulator with QCC-1 connection.

• For use on ”new style” QCC-1 tanks.
• Consists of hose part# 01000 and regulator part# 00920.
• Hose end with SAE 3/8” female flare fitting connects to grill.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. See our flare fitting description for information on measuring and sizes.

Replaces Sams factory part# P3632K

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

Brass orifice. 6mm x 3/4” cone shaped orifice with #64 drill size starter hole. For Electec and other clamp-on valves. Must be drilled to proper drill size.

If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.

Part Number: 31400
Dimensions: 0 3/4” x 0 5/16”
Material: brass
Weight: 0.01

Brass long blunt-end hood orifice drilled to #64 starter hole. Fits valve 3042C, others. Must be drilled to proper drill size.

If you would like us to drill the orifice(s) for you, there is a single $15 fee for this service, which will be added to the order when processed. Please tell us the number of burners in your grill and the total BTUs of your grill (less side burner and rotisserie burner, if any). BTU rating information can usually be found on the grill's CSA certification tag, located somewhere on the grill. Please furnish this, along with any other information you deem relevant, in the Message to CLA box during checkout.

Part Number: 31800
Dimensions: 1 5/16” x 0 9/16”
Material: brass
Weight: 0.1

Clamp-on brass gas valve with straight outlet. Includes orifice.

• D-Value: 12 o'clock
• Stem diameter: 6mm
• Stem length: 1 3/4”

Includes orifice with #72 starter hole. Must be drilled to proper drill size.

Part Number: 3700C
Dimensions: 4 15/16” x 2 1/8”
Material: brass
Weight: 0.5

Shish-ke-bab set. 6 chrome plated 14” skewers with convenient folding rack; folds out to 10” x 13 3/4”.

Part Number: 41338
Weight: 1.1

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Aluminum foil grilling trays. Package of three.

• Heavy duty aluminum foil
• Re-usable
• Great for grilling delicate foods like fish and veggies

Part Number: 50426
Dimensions: 9” x 13”
Weight: 0.4

EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

Part Number: 00030
Weight: 0.1