Sams M3905ALP

P02008004A-R-X3 Main Burners. SET OF THREE (3). Stainless steel center-fed U burners.

Fits Sam's Club Member's Mark LP models:

• M3905ALP
• M5205ALP

Replaces original Member's Mark (Grand Hall) part # P02008004A.
May fit other models

Part Number: P02008004A-R-X3
Dimensions: 16 1/8” x 5 1/8”
Material: stainless steel
Weight: 6.0

P02008004A-R Main Burner. Stainless steel center-fed U burner.

Fits Sam's Club Member's Mark LP models:

• M3905ALP
• M5205ALP

May fit other models.

Replaces original Member's Mark (Grand Hall) part # P02008004A.

Available in an economical 3-burnet set.

Part Number: P02008004A-R
Dimensions: 16 1/8” x 5 1/8”
Material: stainless steel
Weight: 2.0

Premium quality heavy duty stainless steel cooking grid. Our USA-made premium stainless grids are simply the best obtainable. We have them manufactured here in the USA to our specifications and standards, which are high. Of course, they're not available anywhere else.

Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. If you're looking for the best, you've found it. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.

• 304 commercial grade stainless steel
• Large diameter 5/16” solid stainless rods
• Made in USA .
• Sold individually.

See part CLA-GS0004-X2 for a more economical 2-pack.

Replaces Sams factory part# P01604009B

Part Number: CLA-GS0004
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 12”
Material: stainless steel
Weight: 8.5

Aftermarket reversible heavy cast iron cooking grid.

• Sold individually
• Number required varies, check your grill
• Porcelain treated, flat matte finish
• Pointed side is designed for perfect sear marks
• Grooved side captures juices for continous basting

Fits: Broil King 500/625/750 series grills.

NOTE: This aftermarket part, made of the same materials as the original, is a perfect replacement for original part# 22005-281 but at a much lower cost.

Part Number: 22005-281-R
Dimension Front-to-Back: 19 1/4”
Dimension Side-to-Side: 6 1/16”
Material: Cast iron
Weight: 5.0

Porcelain steel cooking grid. Porcelain enameled, glossy finish. Sold individually.

Part Number: 51631
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 5/16”
Material: porcelain steel wire
Weight: 4.0

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually, number required varies, check your grill.

Part Number: 67845-1PC
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 6 1/16”
Material: matte cast iron
Weight: 5.5

Cast iron cooking grids, porcelain treated, flat matte finish for Sams model M3905ALP.

Part Number: 67845
Dimension Front-to-Back: 19 3/16”
Dimension Side-to-Side: 30 5/16”
Material: matte cast iron
Weight: 27.2

Cast iron cooking grid. Porcelain treated, flat matte finish. Sold individually.

Part Number: 69501
Dimension Front-to-Back: 19”
Dimension Side-to-Side: 6 1/8”
Material: cast iron
Weight: 4.85

Ceramic Savor Plate. Measures 7 1/16” x 4 3/4”. Box of 4.

Note: This part is used in racks P01717003E, and P01717002E.

Fits models:

• M3905ALP
• M3905ANG
• M5205ALP
• M5205ANG
• And others

Replaces Sams factory part# P01804006A

Part Number: P01804006A-R
Dimension Front-to-Back: 7 1/16”
Dimension Side-to-Side: 4 3/4”
Material: ceramic
Weight: 4.0

Savor Plate Rack. Heavy duty, 304 premium grade stainless steel with 5/16” rods. Each rack holds three (3) P01804006A-R ceramic flame tamers (sold separately).

NOTE: This is an aftermarket part made to replace original part number P01717003E, which is no longer available.

Fits models:

• M3905ALP
• M3905ANG
• and others

Replaces Sams factory part# P01717003E

Part Number: P01717003E-R
Dimension Front-to-Back: 17 3/8”
Dimension Side-to-Side: 9”
Material: nickel plated steel
Weight: 1.0

Ignitor collector box with ceramic electrode and male round connector.

• Wire not included. Commonly used with wire part# 03400.
• Designed to connect to wires with round female connector.
• If used with existing wire, confirm connector type is round where wire connects to electrode.

See part 02623-X4 for a more econimical 4 pack.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02609001B

Part Number: 02623
Material: ceramic
Weight: 0.2

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502134C

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502134C

Part Number: 03340
Weight: 0.5

Battery powered push button igniter.

• Has two (2) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502192C

Part Number: IGEIB2-B
Weight: 0.3

Universal volt battery powered push button ignitor.

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Sams factory part# P02502192C

Part Number: 03320
Weight: 0.3

Push-button electronic igniter with two (2) spade connectors. Black cap. 1 AAA battery (not included).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG2006
Weight: 0.2

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03400
Weight: 0.1

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Stainless steel grease tray. Hardware included, use old handle. Made in USA

Replaces Sams factory part# P02705165B

Part Number: CLA-DS0122
Dimensions: 15 3/4” x 32 7/8”
Material: stainless steel
Weight: 4.55

Stainless steel lower heat shield for grease tray. Made in USA .

Replaces Sams factory part# P06903028A

Part Number: CLA-MS0124
Dimensions: 10 9/16” x 28 3/4”
Material: stainless steel
Weight: 2.70

Upper heat shield for grease tray with heat shield extension attached (two pieces assembled). Made in USA .

Replaces Sams factory part# P06903029A

Part Number: CLA-MS0123
Dimensions: 10 1/4” x 27 9/16”
Material: stainless steel
Weight: 4.30

Shish-ke-bab set. 6 chrome plated 14” skewers with convenient folding rack; folds out to 10” x 13 3/4”.

Part Number: 41338
Weight: 1.1

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

Part Number: 00030
Weight: 0.1