Nexgrill 720-0336D

Stainless steel burner. Fits premium and designer stainless grills by Charbroil. Includes:

• Made of high quality 304 stainless steel
• Spider exclusion screen
• Ignition electrode mounting holes on both sides of burner
• Back mounting hole is round, inspect your old burner

Replaces Nexgrill factory part# 20002047A0

Part Number: CBP3
Dimensions: 16 15/16
Material: stainless steel
Weight: 1.0

Stainless steel heat plate for Nexgrill model 720-0336D.

Replaces Nexgrill factory part# 04005255A0

Part Number: BBQHP1
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 1/2”
Material: stainless steel
Weight: 0.7

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X4
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.08

SET OF FIVE/5 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X5
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.85

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.77

Porcelain steel Flame Tamer. Sold individually.

Part Number: 90731
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: porcelain steel
Weight: 1.0

Stainless steel Flame Tamer for Nexgrill model 720-0336D.

Part Number: NGHP2
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 1.0

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Burner mounted replacement electrode for use with burner 15641.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Neoprene valve gasket for clamp-on gas control valves. 19mm.

Part Number: 00019
Dimensions: 0 1/2” x 0 1/4”
Material: neoprene
Weight: 0.01

Round heat indicator. Single probe. Requires 13/16” mounting hole.

Replaces Nexgrill factory part# 05001263A0

Part Number: 00745
Dimensions: 3 1/8” x 3 1/8”
Weight: 0.3

6 deluxe chrome plated 22” shish-ke-bab skewers with wooden handles

Part Number: 40538
Material: chrome steel
Weight: 1.1

Deluxe 17” stainless steel turner.

• Soft comfort rubber grip
• Stainless steel blade

Part Number: 43108
Material: stainless steel
Weight: 0.10

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

Abrasive scrubbing brush. Ideal for cleaning porcelain grills.

Part Number: 71448
Weight: 0.2