Turbo Y0665LP (Grand Turbo)

P1961B-R1-X4 Cast Iron Burners. SET OF FOUR(4).

Fits the following Grand Turbo grill models:

• Y0662LP & Y0662NG 6-Burner models
• Y0663LP & Y0663NG 6-Burner models
• Y0665LP & Y0665NG 4-Burner models

This aftermarket part replaces original cast iron Turbo burner part P1961B.

Part Number: P1961B-R1-X4
Dimensions: 16 1/4” x 2 1/16”
Material: cast iron
Weight: 12.4

P1961B-R1 Cast Iron Burner.

Fits the following Grand Turbo grill models:

• Y0662LP & Y0662NG 6-Burner models
• Y0663LP & Y0663NG 6-Burner models
• Y0665LP & Y0665NG 4-Burner models

Also available in more economical 4 and 6 burner multi-packs.

This aftermarket part replaces original cast iron Turbo burner part P1961B.

Part Number: P1961B-R1
Dimensions: 16 1/4” x 2 1/16”
Material: cast iron
Weight: 3.1

Ceramic Flame Tamers for Grand Turbo grills. Measures 7 1/16” x 4 3/4”. Box of 4.

Note: This part is used in racks P1741A, and P1742A.

Fits models:

• Y0662LP/NG
• Y0663LP/NG
• Y0665LP/NG
• And others

Replaces Turbo factory part# P1751A

Part Number: P1751A-R
Dimension Front-to-Back: 7 1/16”
Dimension Side-to-Side: 4 3/4”
Material: ceramic
Weight: 4.0

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Turbo factory part# P2503C

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Turbo factory part# P2503C

Part Number: 03340
Weight: 0.5

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Genuine OEM control knob..

• Off position D-Value: 6 or 12 o'clock
• Knob diameter: 2 1/4”
• Socket diameter: 8mm
• Knob shaft: none (flat)

Part Number: 472-C565
Weight: 0.1

Universal 2 5/16” knob.

• Selectable D-Value
• Selectable socket diameter - 6mm or 8mm.
• Selectable shaft length - flush, 1/4”, or 1 5/8”. Shafts can also be trimmed to desired length.
• Includes 6 shaft inserts and set screw.
• Fits any grill with inside bezel diameter greater than 2 5/16” (the knob diameter).

Replaces Turbo factory part# P03411011L

Part Number: 02342
Dimensions: 2 5/16” x 2 5/16”
Material: plastic
Weight: 0.20

Straight thru L.P regulator with 28” hose. Adequate to 90,000 BTU.

Replaces Turbo factory part# P3632K

Part Number: HR-6B
Dimensions: 28
Weight: 1.50

24” LP hose and regulator with QCC-1 connection.

• For use on ”new style” QCC-1 tanks.
• Consists of hose part# 01000 and regulator part# 00920.
• Hose end with SAE 3/8” female flare fitting connects to grill.

Note: The grill must have a matching SAE 3/8” male flare (standard on most grills), measure to be sure. Due to the SAE standard, the actual dimension of the male SAE 3/8” fitting is much larger, approximately 5/8”. See our flare fitting description for information on measuring and sizes.

Replaces Turbo factory part# P3632K

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

HOW TO GRILL The Complete Illustrated Book of Barbecue Techniques. Steve Raichlen presents a full-color, step-by-step technique book that gets to the core of the grilling experience by showing and telling exactly how it's done. With more than 1,000 photographs, if features over 100 techniques and recipes, from how to set up a three-zone fire to how to grill a perfect prime rib, to grilling pizza, shellfish, vegetables, tofu, fruit, and s'mores.

Part Number: 0-7611-2014-9
Dimensions: 8” x 9 1/4”
Material: Paperback
Weight: 3.0

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

Part Number: 00030
Weight: 0.1