Kenmore 141.17678800

• SS tube burner
• Electrode mounting bracket (not all models use bracket)
• Spider exclusion screen
• Adjustable air shutter.

Replaces Kenmore factory part# P020080324

Replaces Kenmore factory part# P017080074

Replaces Kenmore factory part# P017080074

• Wire not included. Commonly used with wire part# 03400.
• Designed to connect to wires with round female connector.
• If used with existing wire, confirm connector type is round where wire connects to electrode.

See part 02623-X4 for a more econimical 4 pack.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02609009M

• Has two (2) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02502192C

• 1.5 volt
• Has two (2) terminals (male spade connector)
• Uses a single AAA battery (not included)
• Requires 3/4” mounting hole

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Kenmore factory part# P02502192C

For more information about ignition systems and components, please see article Ignition 101 in our help center.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04010-X2, X3, X4, and X5.

• Selectable D-Value
• Selectable socket diameter - 6mm or 8mm.
• Selectable shaft length - flush, 1/4”, or 1 5/8”. Shafts can also be trimmed to desired length.
• Includes 6 shaft inserts and set screw.
• Fits any grill with inside bezel diameter greater than 2 5/16” (the knob diameter).

Replaces Kenmore factory part# P03428073H

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most