Home Depot 730-0954A

Stainless steel burner. Fits premium and designer stainless grills by Charbroil. Includes:

• Made of high quality 304 stainless steel
• Spider exclusion screen
• Ignition electrode mounting holes on both sides of burner
• Back mounting hole is round, inspect your old burner

Part Number: CBP3
Dimensions: 16 15/16
Material: stainless steel
Weight: 1.0

Stainless steel cooking grids. Sold as a set of three (3).

Part Number: 5S773
Dimension Front-to-Back: 18 13/16”
Dimension Side-to-Side: 26 5/8”
Material: stainless steel wire
Weight: 14.3

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X4
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.08

SET OF FIVE/5 PACK Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158-X5
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 3.85

Stainless steel heat plate/Flame Tamer. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0158
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.77

Porcelain steel Flame Tamer. Sold individually.

Part Number: 90731
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: porcelain steel
Weight: 1.0

Stainless steel Flame Tamer for Home Depot model 730-0954A.

Part Number: NGHP2
Dimension Front-to-Back: 16 1/8”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 1.0

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has six (6) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03356
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

20” Ignitor adapter wire with female spade connector and male round connector. Used primarily on Ducane models 7100 and 7200 to extend the wire from the 03758 collector box and electrode to the electronic spark generator (igniter).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03750
Dimensions: 1/16
Weight: 0.05

Electrode with 24.5” wire that has a female spade/flat end for Home Depot model 730-0954A. To lengthen the wire use adapter # 03198 and extension wire # 03750.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 04432
Dimensions: 4”
Material: ceramic
Weight: 0.1

electrode with connection

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 04436
Material: ceramic
Weight: 1.0

Universal 2 5/8” adapter wire with female round and male spade connectors. Primarily used when connecting spark generators (ignitors) to electrode wires with unlike connectors. Typically, push-button and rotory piezo spark generators have male round connectors, while battery operated electronic spark generators usually have male spade connectors.

• Can change male round to male spade
• Can change female spade to female round

ALL

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03198
Weight: 0.05

Burner mounted replacement electrode for use with burner 15641.

• Ceramic insulator
• Wire with female spade connector

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03351
Material: ceramic
Weight: 0.2

Round heat indicator. Single probe. Requires 13/16” mounting hole.

Part Number: 00745
Dimensions: 3 1/8” x 3 1/8”
Weight: 0.3

Texas hickory flavor wood chips. 800g.

Part Number: 00220
Weight: 2.0

20” Professional Extra Long Tong.
20” Stainless steel tong with red soft grip rubber inserts. Grip your food on the grill with ease. Manual lock saves on storage space.

Part Number: 40269
Material: stainless steel
Weight: 0.14

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Upright porcelain steel roasting rack with grid topper.

Part Number: 40935
Weight: 2.9

Abrasive scrubbing brush. Ideal for cleaning porcelain grills.

Part Number: 71448
Weight: 0.2