Great Outdoors A052041

Replacement stainless steel burner. Includes venturi mounting bolts/screws. Venturi not included, sold separately.

NOTE: The original cast brass and cast iron burners are no longer available. This replacement stainless steel version is slightly smaller, but supports the same amount of gas with good heat distribution. The stainless steel version will not screw down into the base of the grill, but simply sits in the bottom of the grill using adjustable support brackets, which are included.

Part Number: AZ001505-SS
Dimensions: 15 7/8” x 8”
Material: stainless steel
Weight: 2.5

AZ001505-R Replacement cast iron burner. Includes venturi mounting bolts. Venturi not included, sold separately. Replaces original Great Outdoors part# AZ001505.

Fits models:

• 4000
• A052041

NOTE: The original Great Outdoors cast brass and cast iron burners are no longer available. This replacement burner is slightly larger, but fully functional. It's ”legs” are not threaded, so it simply sits in the bottom of the grill.

Part Number: AZ001505-R
Dimensions: 15 1/2” x 8”
Material: cast iron
Weight: 7.0

Spider exclusion screens. Installs over venturi air shutters to keep spiders out. Approximately 7/8” in diameter and 1” long.

Part Number: 70002
Dimensions: 1” x 7/8”
Material: stainless steel
Weight: 0.1

AZ000507-R Replacement venturi tube. Includes gasket and screws. Replaces original Great Outdoors part# AZ000507.

Fits models:

• 4000
• A052041

NOTE: The original OEM venturi and aftermarket replacements are no longer available. Using two adjustable single venturis, slightly modified, we have created a working replacement that, whie not perfect, works well.

Part Number: AZ000507-R
Dimensions: 5 1/2” x 6 1/8”
Material: chrome steel
Weight: 0.8

Premium quality stainless steel cooking grid. Far superior to the porcelain coated steel grids it replaces.

• Made in USA
• 304 commercial grade stainless steel
• Solid .225 diameter stainless rods
• Sold individually

Fits grill by Arkla, Arklamatic, Charbroil, Charmglow, Embermatic, Great Outdoors, Kenmore, Kmart, Martha Stewart, Roper, Vermont Castings, Weber. May fit others.

Part Number: 58671-SS
Dimension Front-to-Back: 14 3/4”
Dimension Side-to-Side: 21 1/2”
Material: Stainless steel
Weight: 5

Carbon steel rock grate with 1/4” rods. Made in USA .

Replaces Great Outdoors factory part# AF000203

Part Number: CLA-RX0007
Dimensions: 13” x 19”
Material: carbon steel
Weight: 4.5

Heat Shield. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Replaces Great Outdoors factory part# AI000204

Part Number: CLA-MS0067
Dimensions: 10 1/4” x 16 3/8”
Material: stainless steel
Weight: 1.4

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

36” wire with two female spade connectors for side burner igniters (not for use with rotary or piezo ignitors).

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03500
Weight: 0.05

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Universal collector box with electrode and wire. Fits most H burners, cast iron and stainless. Mounts to burner using venturi screws. Slotted construction allow universal adjustment of electrode position.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-15B
Weight: 0.3

Snap In Piezo Ignitor. Fits Weber Genesis Silver A,B,C and Newer Spirit E310 & E320.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: UP-9B
Weight: 0.2

Collector box and ceramic electrode with male spade connector. Will not work with original wire, which is attached directly to the original electrode. Requires two (2) 03400 wires with female spade connectors. Mounts perpendicular through casting with threaded rod and locking nuts. Includes igniter ground lug, no wire.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Great Outdoors factory part# AN000103

Part Number: 03800
Material: ceramic
Weight: 0.2

25” wire with female spade connector on one end, and female round connector on the other end. Commonly used to connect electrodes to igniters. Typical installation is round connector to electrode, spade (flat) connector to igniter.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Great Outdoors factory part# AN000203

Part Number: 03400
Weight: 0.1

Push-Button self-grounding piezo spark generator; requiers 3/4” mounting hole. Primary connector is a round male connector, so connecting wire needs to be female round connector. If needed, see part# 03199C for a short adapter wire that converts flat female spade connectors to female round. Secondary connector is a flat male spade connector used to conduct spark to a secondary electrode, such as a side burner, or used as a ground in some applications. See ground wire part# 03620. For more information, see our article Ignition 101.

Replaces Great Outdoors factory part# AN000304

Part Number: 03120
Weight: 0.1

24” LP hose with QCC-1 type one regulator. For use on ”new style” tanks. Use with 34100 twin manifold.

Part Number: 80012
Dimensions: 23 1/2” x 0 1/2”
Weight: 0.80

T manifold for twin valves with 3/8” male flare. Use with hose & regulator #80012.

Part Number: 34100
Dimensions: 2” x 1 5/16”
Material: brass
Weight: 0.3

Durable 2 5/16” round briquettes

• Self-cleaning
• Control flare-ups while holding an even heat pattern.
• About 53 pieces, covers approximately 275 sq. inches.
• Fits all gas grills

Part Number: BQ-5
Weight: 7.2

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

10” Bamboo Skewers (100 pieces)

• Ideal for grilling meat and vegetables
• Soak skewers in water about 1/2 hour before using
• Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
• Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.

Part Number: 11060
Weight: 0.6

Natural lava rock processed and screened for uniformity. 7 lb. bag is enough for all full sized grills. Click the photo to find easy steps for installing lava rocks.

Part Number: 45887
Material: pummise
Weight: 7.0

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Stainless steel WOK topper with serving handles. Ideal for seafood and vegatables.

Part Number: 96321
Dimensions: 12 3/4” x 12 3/4”
Material: stainless steel
Weight: 1.6

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3