Ducane 30732301 (Affinity 3400)

Stainless steel burners. SET OF THREE (3). Fits Ducane Affinity series grill models.

Part Number: 19351-X3
Dimensions: 18” x 1”
Material: stainless steel
Weight: 2.7

Stainless steel burner. Fits Ducane Affinity series grills models.

Part Number: 19351
Dimensions: 18” x 1”
Material: stainless steel
Weight: 0.9

Cast iron cooking grids (set of 2). Porcelain enameled, glossy finish.

Part Number: 68502
Dimension Front-to-Back: 18”
Dimension Side-to-Side: 28 3/4”
Material: gloss cast iron
Weight: 14.12

Stainless steel cooking grid for Ducane Affinity grills.

• 304 commercial grade stainless steel
• 1/4” solid stainless rods
• Dimensions: 18” x 11 7/8”
• Made in USA .
• Sold individually.

Unlike the OEM Ducane grids these replace, these high quality made-in-the-USA grids are made of high quality 304 stainless steel that resists rust and corrosion far more than the originals.

Replaces Ducane factory part# 30501011

Part Number: CLA-GS0065
Dimension Front-to-Back: 18”
Dimension Side-to-Side: 11 7/8”
Material: stainless steel
Weight: 4.2

Stainless steel heat distribution plate for Ducane Affinity grills. Sold individually, number required varies. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0044
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 6”
Material: stainless steel
Weight: 0.8

Left stainless steel heat plate for Affinity 3400 and 4400 series grills. Affinity grills equipted with rotisserie burners require two notched heat plates, a left and a right. This is in addition to one (3-burner models) or two (4-burner models) of the un-notched heat plate CLA-TS0044. Sold individually. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0044L
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 6”
Material: stainless steel
Weight: 0.8

Right stainless steel heat plate for Affinity 3400 and 4400 series grills. Affinity grills equipted with rotisserie burners require two notched heat plates, a left and a right. This is in addition to one (3-burner models) or two (4-burner models) of the un-notched heat plate CLA-TS0044. Sold individually. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0044R
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 6”
Material: stainless steel
Weight: 0.8

Porcelain steel Heat Distribution Plate. Sold individually.

Part Number: 99351
Dimension Front-to-Back: 15 3/8”
Dimension Side-to-Side: 6”
Material: porcelain steel
Weight: 1.6

Push-button electronic igniter with four (4) spade connectors. Black cap. Uses one AAA battery (not included). Requires a 3/4” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: TS-IG4010
Weight: 0.2

electrode assembly for use with Weber models with spark generators that have an external grounding prong. Includes mounting tabs to facilitate installation.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 04800
Material: ceramic
Weight: 0.2

Battery powered push button igniter.

• Has four (4) spade type male connectors.
• Uses 1 AAA battery (not supplied)
• Requires 3/4” or 13/16” mounting hole.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IGEIB4-B
Weight: 0.3

Universal four-outlet battery powered push button ignitor.

• 1.5 volt
• Has four (4) terminals (male spade connector)
• Uses a single AA battery (not included)
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03340
Weight: 0.5

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

14” ground wire with female spade connector and eye connectors. For use with 1.5 volt (AA or AAA) spark generators including 03340 and 03350.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03620
Weight: 0.1

Texas hickory flavor wood chips. 800g.

Part Number: 00220
Weight: 2.0

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Deluxe non-stick chicken and rib tumble basket. Attaches to rotisserie spit rod.

• Ideal for cooking pieces of meat or vegetables
• Self basting, easy to use
• Locks on spit rod with thumb screw (supplied)
• 6 1/2” x 10” long

Part Number: 24764
Dimensions: 6 1/2” x 10”
Weight: 1.1

Abrasive scrubbing brush. Ideal for cleaning porcelain grills.

Part Number: 71448
Weight: 0.2