Charbroil 466270610 (Quantum Infrared)

Stainless steel burner for Charbroil model 466270610.

Replaces Charbroil factory part# G515-2200-W1

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

Stainless steel cross-over burner for Charbroil model 466270610.

Replaces Charbroil factory part# G515-0044-W1

Part Number: 05596
Dimensions: 8 1/2” x 0 3/4”
Material: stainless steel
Weight: 0.1

Stamped stainless steel cooking grids. Sold as a set of two (2). Each panel is an emitter tray and a grid-in-tray assembly, a total of 4 pieces.

Part Number: 5S482
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 17 3/4”
Material: stamped stainless steel
Weight: 10.6

Stamped stainless steel cooking grids (set of 3). Each grid is a grid-in-tray assembly, so there is actually a total of 6 pieces.

Part Number: 5S483
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 15.4

Infrared slotted stamped stainless steel cooking grid that features slotted grease drain holes for improved performance. SOLD AS A SET OF TWO (2) PIECES ONLY.
WARNING: This cooking grid set does not include the bottom trays. The grid-in-tray set of four pieces was discontinued by our supplier.

Replaces Charbroil factory part# G515-4700-W1

Part Number: 5S472
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 17 3/4”
Material: stamped stainless steel
Weight: 5.5

Stamped stainless steel cooking grids. SOLD AS A SET OF THREE (3) PIECES ONLY.
WARNING: This cooking grid set does not include the bottom trays. For the grid in tray set see part # 5S483.

Replaces Charbroil factory part# G515-4800-W1

Part Number: 5S473
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 8.0

SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141-X4
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 3.92

Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.98

Stainless steel aftermarket Flame Tamer heat plate.

• Stainless equivalent of part 93321
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 93321-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.7

Porcelain steel Flame Tamer. Sold individually.

Replaces Charbroil factory part# G501-0008-W1

Part Number: 93321
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 1.0

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has two (2) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Charbroil factory part# G350-0017-W1

Part Number: 03322
Dimensions: 2 5/8” x 2”
Weight: 0.5

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Charbroil factory part# G515-0017-W1A

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Replaces Charbroil factory part# G515-0067-W1

Part Number: 01472
Material: ceramic
Weight: 0.1

Semi-circular, snap in heat indicator with 2 3/4” heat prob for Charbroil model 466270610.

Replaces Charbroil factory part# G516-0008-W1

Part Number: 00473
Dimensions: 1 3/4” x 1 3/16”
Material: stainless steel
Weight: 0.1

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Stainless steel chicken roaster. Commonly called Beer Can roasters.

• The best way to roast poultry on the grill
• For use in barbecues and ovens
• Dishwasher safe
• Includes rack, rack support, and basting brush

Part Number: 41333
Material: stainless steel
Weight: 0.10

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3