Charbroil 466224611 (Precision Flame Infrared)

Stainless steel burner for Charbroil model 466224611.

Replaces Charbroil factory part# G517-7300-W1

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

stainless steel cross-over burner for Charbroil model 466224611.

Replaces Charbroil factory part# G614-0095-W1A

Part Number: 05592
Dimensions: 6 3/8” x 0 13/16”
Material: stainless steel
Weight: 0.1

Stamped stainless steel cooking grids (set of 3). Each grid is a grid-in-tray assembly, so there is actually a total of 6 pieces.

Part Number: 5S483
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 15.4

Stamped stainless steel cooking grids. SOLD AS A SET OF THREE (3) PIECES ONLY.
WARNING: This cooking grid set does not include the bottom trays. For the grid in tray set see part # 5S483.

Replaces Charbroil factory part# G519-4500-W1

Part Number: 5S473
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 8.0

SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141-X4
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 3.92

Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.98

Stainless steel aftermarket Flame Tamer heat plate.

• Stainless equivalent of part 93321
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 93321-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.7

Porcelain steel Flame Tamer. Sold individually.

Replaces Charbroil factory part# G614-0045-W1

Part Number: 93321
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 1.0

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Replaces Charbroil factory part# G515-0014-W1

Part Number: 01472
Material: ceramic
Weight: 0.1

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Charbroil factory part# G515-0017-W1A

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Semi-circular, snap in heat indicator with 2 3/4” heat prob for Charbroil model 466224611.

Replaces Charbroil factory part# G516-0008-W1

Part Number: 00473
Dimensions: 1 3/4” x 1 3/16”
Material: stainless steel
Weight: 0.1

shishkebob skewers

Part Number: 46074
Dimensions: 18” x 0 5/8”
Material: stainless steel
Weight: 0.4

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Aluminum foil grilling trays. Package of three.

• Heavy duty aluminum foil
• Re-usable
• Great for grilling delicate foods like fish and veggies

Part Number: 50426
Dimensions: 9” x 13”
Weight: 0.4

Replacement heads for grill brush 77600. Set of two.

Part Number: 77650
Weight: 0.3