Charbroil 464222009

Stainless steel burner for Charbroil model 464222009.

Replaces Charbroil factory part# 80017579

Part Number: CBP5
Dimensions: 15 7/8” x 1”
Material: stainless steel
Weight: 1.0

Stainless steel burner for Charbroil model 464222009.

Replaces Charbroil factory part# 80017579

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

stainless steel cross-over burner for Charbroil model 464222009.

Replaces Charbroil factory part# 80017595

Part Number: 05592
Dimensions: 6 3/8” x 0 13/16”
Material: stainless steel
Weight: 0.1

Premium stainless steel cooking grids. Set of two (2) grids. Far superior to porcelain coated steel grids.

• Made in USA
• Commercial grade 304 stainless steel
• 5/16” solid stainless rods
• Sold as a set of two (2).

Each panel measures:

• Front-to-Back: 18 1/2”
• Side-to-Side: 12 3/4”

Total Side-to-Side: 25 1/2”

Part Number: 54712-SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 5.0

Premium quality stainless steel cooking grid. Far superior to the porcelain coated steel grids it replaces.

• Made in USA
• 304 commercial grade stainless steel
• Solid 5/16” diameter solid stainless rods
• Sold individually

Fits grills made by Charbroil, Kenmore, Master Chef and others.

Part Number: 54712-SS
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 12 3/4”
Weight: 2.5

Stainless Steel cooking grids. SET OF TWO (2) panels.

• Made in USA
• Solid 5/16” 304 stainless rods
• Each panel measures 18 1/2” x 12 3/4”
• Overall dimensions: 18 1/2” x 25 1/2”

Part Number: CG-109SS-X2
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 25 1/2”
Weight: 15.0

Porcelain steel Flame Tamer. Sold individually.

Replaces Charbroil factory part# 80018323

Part Number: 94491
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: porcelain steel
Weight: 1.1

Stainless steel aftermarket Flame Tamer.

• Stainless equivalent of part 94491
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 94491-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 5 3/4”
Material: stainless steel
Weight: 0.7

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Replaces Charbroil factory part# 80007512

Part Number: 01472
Material: ceramic
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has six (6) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Charbroil factory part# 80018306

Part Number: 03356
Dimensions: 3 3/8” x 2”
Weight: 0.7

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Round 2 3/8” diameter heat indicator, includes one wing nut and one locking nut.

• Requires minimum 3/8” mounting hole
• Single 1 3/8” probe
• Threaded portion of probe stops at 1/2” from base
• See photo for details

Replaces Charbroil factory part# 80007690

Part Number: 00012
Dimensions: 2 3/8” x 2 3/8”
Weight: 0.1

6 deluxe chrome plated 22” shish-ke-bab skewers with wooden handles

Part Number: 40538
Material: chrome steel
Weight: 1.1

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

economy basting brushes. Two brushes, 7.5” long.

Part Number: 43054
Weight: 0.1

Upright porcelain steel roasting rack with grid topper.

Part Number: 40935
Weight: 2.9

Grill Mitt With Neoprene Palm.

16 in. silicone mitt diffuses heat away from the hand and washes easily. Black palm / red colored cuff. Cotton lined.
*One Size Fits Most

Part Number: 90963
Weight: 0.5