Charbroil 463273012 (Performance Infrared)

Stainless steel burner for Charbroil model 463273012.

Replaces Charbroil factory part# G515-2200-W1

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

stainless steel cross-over burner for Charbroil model 463273012.

Replaces Charbroil factory part# G516-0006-W1

Part Number: 05595
Dimensions: 7 7/16” x 0 3/4”
Material: stainless steel
Weight: 0.1

Cast iron cooking grates. SET OF FOUR (4). Porcelain treated, flat matte finish. For some grill models, these cast iron grates sit atop stainless grate such as our part# 5S574.

Each panel measures:

• 18 5/16” Front-To-Back
• 7 3/16” Side-To-Side

Part Number: 61134
Dimension Front-to-Back: 18 5/16”
Dimension Side-to-Side: 28 3/4”
Material: matte cast iron
Weight: 22.9

Cast iron cooking grids (set of 3). Porcelain treated, matte finish.

Part Number: 65993
Dimension Front-to-Back: 18 1/8”
Dimension Side-to-Side: 30 9/16”
Material: matte cast iron
Weight: 25.5

Stamped stainless steel cooking grid in tray set, eight (8) pieces.

• Four (4) stainless trays, 18 3/8” x 7 11/16”
• Four (4) stainless cooking grids 17 1/16” x 7 7/16”

Part Number: 5S584
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 30 3/4”
Material: stamped stainless steel
Weight: 18.3

Stamped stainless steel cooking grates. SET OF FOUR (4) TOP PIECES ONLY DOES NOT INCLUDE TRAY; IS NOT A GRID IN TRAY.

Each panel measures:

• 18 7/16” Front-To-Back
• 7 3/4” Side-To-Side

On some models, these grates are used in conjunction with cast iron grates that rest on top of the stainless grates. See our part# 61134 for a set designed to fit on top of 5S574.

Also, see our part# 65993 for an economical all cast iron solution.

Replaces Charbroil factory part# G520-8900-W1

Part Number: 5S574
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 30 3/4”
Material: stamped stainless steel
Weight: 9.0

SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141-X4
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 3.92

Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.98

Stainless steel aftermarket Flame Tamer heat plate.

• Stainless equivalent of part 93321
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 93321-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.7

Porcelain steel Flame Tamer. Sold individually.

Replaces Charbroil factory part# G501-0008-W1

Part Number: 93321
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 1.0

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Replaces Charbroil factory part# G515-0014-W1

Part Number: 01472
Material: ceramic
Weight: 0.1

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Replaces Charbroil factory part# G515-0017-W2A

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Semi-circular, snap in heat indicator with 2 3/4” heat prob for Charbroil model 463273012.

Replaces Charbroil factory part# G516-0008-W1

Part Number: 00473
Dimensions: 1 3/4” x 1 3/16”
Material: stainless steel
Weight: 0.1

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7