Charbroil 463225315 (Performance)

Stainless steel burner for Charbroil model 463225315.

Part Number: 14741
Dimensions: 15 15/16” x 1”
Material: stainless steel
Weight: 0.5

stainless steel cross-over burner for Charbroil model 463225315.

Part Number: 05592
Dimensions: 6 3/8” x 0 13/16”
Material: stainless steel
Weight: 0.1

Reversible, heavy cast iron cooking grids. Porcelain treated, flat matte finish. SOLD INDIVIDUALLY

Part Number: 66652-1PC
Dimension Front-to-Back: 18 1/4”
Dimension Side-to-Side: 13 1/8”
Material: matte cast iron
Weight: 10.0

Premium universal cooking grids. Set of two (2) grids. Porcelain treated cast iron. Matte finish.

Each panel measures:

• Front-to-Back: 18 1/4”
• Side-to-Side: 13 1/8”

Total Side-to-Side: 26 1/4”

Part Number: 66652-UNI-X2
Dimension Front-to-Back: 18 1/4”
Dimension Side-to-Side: 26 1/4”
Material: cast iron
Weight: 18.8

Premium universal cooking grid. Porcelain treated cast iron. Matte finish. Sold individually. See part 66652-UNI-X2 for a set of two (2) grids.

Part Number: 66652-UNI
Dimension Front-to-Back: 18 1/4”
Dimension Side-to-Side: 13 1/8”
Material: cast iron
Weight: 9.4

Stamped stainless steel cooking grids (set of 3). Each grid is a grid-in-tray assembly, so there is actually a total of 6 pieces.

Part Number: 5S483
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 15.4

Reversible, heavy cast iron cooking grids. Porcelain treated, flat matte finish. Sold as a set of two (2).

Part Number: 66652
Dimension Front-to-Back: 18 1/4”
Dimension Side-to-Side: 26 1/4”
Material: matte cast iron
Weight: 19.35

Stamped stainless steel cooking grids. SOLD AS A SET OF THREE (3) PIECES ONLY.
WARNING: This cooking grid set does not include the bottom trays. For the grid in tray set see part # 5S483.

Replaces Charbroil factory part# G519-A400-W1

Part Number: 5S473
Dimension Front-to-Back: 18 7/16”
Dimension Side-to-Side: 26 5/8”
Material: stamped stainless steel
Weight: 8.0

SET OF FOUR/4 PACK Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141-X4
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 3.92

Flame Tamer, stainless steel. Made in USA .

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0141
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.98

Stainless steel aftermarket Flame Tamer heat plate.

• Stainless equivalent of part 93321
• Superior to the porcelain steel originals
• Rust and corrosion restitant
• Sold individually
• Made in USA

Part Number: 93321-SS
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.7

Porcelain steel Flame Tamer. Sold individually.

Part Number: 93321
Dimension Front-to-Back: 16”
Dimension Side-to-Side: 3 13/16”
Material: porcelain steel
Weight: 1.0

Electrode, gas collector box, and wire. The connecting wire has a flat female spade connector, which is typically used with electronic (battery operated) ignitors (see Ignition 101 in our help center).

NOTE: This electrode is also sometimes used with push-button or rotary piezo ignitors, such as our part# 03100 and 03120, which have round connectors. When connecting 01472 electrode to ignitors with round connectors, use short wire part# 03199C to convert the electrode wire from a femal spade connector to a female round connector.

Part Number: 01472
Material: ceramic
Weight: 0.1

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Universal 2 3/4” adaptor wire with a round female end and a male spade end that has a protective cover.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03199C
Weight: 0.05

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Semi-circular, snap in heat indicator with 2 3/4” heat prob for Charbroil model 463225315.

Part Number: 00473
Dimensions: 1 3/4” x 1 3/16”
Material: stainless steel
Weight: 0.1

HOW TO GRILL The Complete Illustrated Book of Barbecue Techniques. Steve Raichlen presents a full-color, step-by-step technique book that gets to the core of the grilling experience by showing and telling exactly how it's done. With more than 1,000 photographs, if features over 100 techniques and recipes, from how to set up a three-zone fire to how to grill a perfect prime rib, to grilling pizza, shellfish, vegetables, tofu, fruit, and s'mores.

Part Number: 0-7611-2014-9
Dimensions: 8” x 9 1/4”
Material: Paperback
Weight: 3.0

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Marinade Injector.

For injecting flavor and marinades into meat. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

Part Number: 00030
Weight: 0.1