Brinkmann 810-3660-0

Stainless steel sear burner with attached electrode tab. This is a rather unique burner. It has a tube attached to one inner side of the burner that has flame ports and the end is plugged; it does not attach to the other side. This burner does not exactly resemble the original burner OEM # 154-3660-0 for some Brinkmann models, however it is a very good replacement burner.

Part Number: 13461
Dimensions: 15 3/8” x 4 3/8”
Material: stainless steel
Weight: 0.7

Stainless steel burner for OEM # 154-9520-0 for Brinkmann model 810-3660-0.

Replaces Brinkmann factory part# 154-3660-0

Part Number: BMTB3
Dimensions: 15 5/16
Material: stainless steel
Weight: .70

Stainless steel burner for Brinkmann model 810-3660-0.

Part Number: 19511
Dimensions: 15 3/8” x 1”
Material: stainless steel
Weight: 0.7

Stainless steel burner cross-over tube for Brinkmann model 810-3660-0.

Part Number: 09423
Dimensions: 7 5/8” x 2 3/8”
Material: stainless steel
Weight: 0.2

Cast iron cooking grids. SET OF FOUR (4).

• Porcelain treated, matte finish
• 4 panels, each 17 5/8” x 8 3/4”
• Total width: 35”

Part Number: CG-73P-CI-X4
Dimension Front-to-Back: 17 5/8”
Dimension Side-to-Side: 35”
Material: cast iron
Weight: 22.20

Cast iron cooking grids (set of 4). Porcelain treated, flat matte finish.

Part Number: 64104
Dimension Front-to-Back: 17 5/8”
Dimension Side-to-Side: 35 1/2”
Material: cast iron
Weight: 14.1

SET OF FOUR/4 PACK Stainless steel Heat Distribution Plates. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0135-X4
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 3 7/8”
Material: stainless steel
Weight: 2.64

Stainless steel Heat Distribution Plate. Made in USA .

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0135
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 3 7/8”
Material: stainless steel
Weight: 0.66

Stainless steel Heat Distribution Plate for Sear Burner. Sold individually.

Part Number: 93661
Dimension Front-to-Back: 15 5/16”
Dimension Side-to-Side: 5 1/8”
Material: stainless steel
Weight: 0.8

Porcelain steel Heat Distribution Plate. Sold individually.

Part Number: 92311
Dimension Front-to-Back: 15 3/8”
Dimension Side-to-Side: 3 15/16”
Material: porcelain steel
Weight: 0.63

Ignition connection wire used to connect battery powered spark generators to electrodes. One 47” wire.

• Wire has female spade connector on one end and square plastic connector on the other
• Square plastice connector attaches to spark generator
• Female spade connector ataches to electrode

See part 03610-X4 for a more economical 4-pack.

NOTE: For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Part Number: 03610
Weight: 0.05

Burner mounted electrode with male spade connector. Includes small mounting bolt and nut.

• Wire not included. Commonly used with wire part# 03610.
• Female spade connector on wire connects to male spade connector of electrode.
• If used with existing wire, confirm connecting end of wire is a female spade connector
• Usually, one electrode required per burner

NOTE: Electrodes provide the spark that ignites the gas when the ignitor button is depressed, or the knob is turned. They're the spark plug of the grill. ==> For more information on grill ignition systems, including how to connect electrodes to spark generators/ignitors, see article Ignition 101 in our help center.

Also available in more economical 2, 3, 4, and 5 piece multi-packs. See part 04022-X2, X3, X4, and X5.

Part Number: 04022
Material: ceramic
Weight: 0.1

Round 2 3/8” diameter heat indicator, includes one wing nut and one locking nut.

• Requires minimum 3/8” mounting hole
• Single 1 3/8” probe
• Threaded portion of probe stops at 1/2” from base
• See photo for details

Part Number: 00012
Dimensions: 2 3/8” x 2 3/8”
Weight: 0.1

10” Bamboo Skewers (100 pieces)

• Ideal for grilling meat and vegetables
• Soak skewers in water about 1/2 hour before using
• Use foods that require the same amount of cooking time. Meats can be pre-cooked. Marinated foods are recommended for added flavor.
• Great for chicken or beef, ham, lamb, or veal, salami, shrimp, or scallops, mushrooms, sliced peppers, omion, carrots, cherrytomatoes, pineapples, zuccini, and apples.

Part Number: 11060
Weight: 0.6

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Deluxe 13” basting mop with hardwood handle and cotton mop head.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Deluxe non-stick flat spit basket. Attaches to 3/8” rotisserie rod with adjustable lid to secure food. 16”x7.5”x2”
WARNING: Before ordering, please verify that your rotisserie spit rod can fit through the .48 inch x .48 squared mounting holes. Our spit rod part numbers SR-5, SR-8 and SR-43 do fit.

Part Number: 24785
Dimensions: 7 1/2” x 16”
Weight: 1.5

deluxe 18” grill brush with hardwood handle with stainless steel bristles and scraper
MFGR BACK ORDER. This part is on back order with the manufacturer. Orders for this part will be filled when new stock arrives, which could be in two weeks, or two months.

Part Number: 70255
Dimensions: 18 5/8” x 3 1/2”
Weight: 0.7